Прошивка онушек BDCOM
Подключаем онушку к голове (olt) bdcom. Потом делаем:
- show running-config interface epoN 0/1
Building configuration...
Current configuration: ! interface EPON0/1
epon bind-onu mac fcfa.f7c5.f31a 1
или
- show epon onu-information
Interface EPON0/1 has registered 1 ONUs: IntfName VendorID ModelID MAC Address Description BindType Status
Dereg Reason
EPON0/1:1 BDCM 3022 fcfa.f7c5.f31a N/A static auto_conf igured N/A
что бы увидеть на каком порту висит интересуемая нас онушка.
После этого проверяем версию ее прошивки:
- show epon interface EPON 0/1:1 onu ctc basic-info
ONU Vender ID : BDCM ONU MODEL ID : 3022 ONU ID : fcfa.f7c5.f31a Hardware Version : A0 Software Version : 10.0.14A:1032 Firmware Version : 0x010000 Chipset Vendor ID : E0 Chipset MODEL ID : 0x8829 Chipset Revision : 160 Chipset Date : 11/06/01 Onu type : SFU Support multillid : Not supported Protection type : Not supported Number of Pon : 1 Number of slot : 0 Support 1 types of port:
Number of GE port : 1
Battery Backup : 0
Если версия ниже чем: 10.0.14A:1039 для модели 3022 - значит нам нужно прошивать даную onuшку.
Для этого делаем следующее:
- epon update onu image p1501c.bin interface epoN 0/1:1
нажимаем "y" и ждем, примерно 5 минут.
Are you sure to update the ONU image(y/n)?y %ONU-UPDATE: Load image to memory may take some time, please wait... Loading p1501c.bin..... ++++++++++++++++++++++++++++++++++++++++++++++++++++++++ %ONU-UPDATE: File p1501c.bin len 450304 Byte. Switch#Jan 1 00:15:39 CTC ONU(0x60c30000) upgrade start... Wait. Jan 1 00:15:39 The image is downloading to the ONU on EPON0/1:1, Please wait! The onu will reboot when downloading finished, and then you can check the software version after re-registration! ..........................................................................................................................................................................................................Q CTC OAM UPGRADE OK,PLS COMMIT AFTER ONU REBOOT Jan 1 00:16:19 ONU has completed writing to flash Jan 1 00:16:19 CTC_OAM_ONU_UPGRADE_ACTIVATE_IMG_REQ Jan 1 00:16:19 Activate image request/response successful Jan 1 00:16:23 %LINE-5-UPDOWN: Line on Interface EPON0/1, changed state to down Jan 1 00:16:23 %LINEPROTO-5-UPDOWN: Line protocol on Interface EPON0/1, changed state to down Jan 1 00:16:23 %LINEPROTO-5-UPDOWN: Line protocol on Interface VLAN1, changed state to down Jan 1 00:16:23 %EPON-ONUDEREG: ONU fcfa.f7c5.f31a is deregistered on EPON0/1:1. Jan 1 00:16:29 %LINE-5-UPDOWN: Line on Interface EPON0/1, changed state to up Jan 1 00:16:29 %LINEPROTO-5-UPDOWN: Line protocol on Interface EPON0/1, changed state to up Jan 1 00:16:29 %LINEPROTO-5-UPDOWN: Line protocol on Interface VLAN1, changed state to up Jan 1 00:16:29 %EPON-ONUREG: ONU fcfa.f7c5.f31a is registered on EPON0/1:1. Jan 1 00:16:29 %EPON-ONUAUTHEN: ONU fcfa.f7c5.f31a is authenticated on EPON0/1:1. Jan 1 00:16:30 %OLT: Interface EPON0/1:1's OAM Operational Status: Operational Jan 1 00:16:33 %OLT: Interface EPON0/1:1's CTC OAM extension negotiated successfully! Jan 1 00:16:33 ONU register on interface EPON0/1:1 for the first time! Jan 1 00:16:33 ONU register on interface EPON0/1:1 again!
Если все ок - зачит идем дальше:
- epon commit-onu-image-update interface ePON 0/1
CTC OAM UPGRADE FINISHED Jan 1 00:18:56 Commit image request/response successful Jan 1 00:18:56 Commit onu image update successfully on EPON0/1:1!
Снова проверяем версию прошивки:
- show epon onu-information
Interface EPON0/1 has registered 1 ONUs: IntfName VendorID ModelID MAC Address Description BindType Status
Dereg Reason
--------- -------- -------------- --------------- --------- ---------
-----------------
EPON0/1:1 BDCM 3022 fcfa.f7c5.f31a N/A static auto_conf igured N/A
Switch#show epon interface EPON 0/1:1 onu ctc basic-info ONU Vender ID : BDCM ONU MODEL ID : 3022 ONU ID : fcfa.f7c5.f31a Hardware Version : A0 Software Version : 10.0.14A:1039 Firmware Version : 0x010000 Chipset Vendor ID : E0 Chipset MODEL ID : 0x8829 Chipset Revision : 160 Chipset Date : 11/06/01 Onu type : SFU Support multillid : Not supported Protection type : Not supported Number of Pon : 1 Number of slot : 0 Support 1 types of port:
Number of GE port : 1
Battery Backup : 0
Все готово. Эту онушку можно устанавливать у клиентов. И она нормально заработает на ZTE.
На самой ЗТЕ посмотреть как то так, но не всегда это получается.
ZTE-C300-Office#show remote onu info epon-onu_1/6/5:17 epon-onu_1/6/5:17 Onu vendorId BDCM . Onu type ZTE-F420. OnuModel 3022. OnuId fcfa.f7c5.e5ad. Hardware version A0. Software version 10.0.14A:1039. Firmware version 1.0.0(HEX). Chip vendorId Opulan. ChipModel 0x8829. Chip revison 160. ChipDesignDate 11/06/01 (HEX: 0B/06/01). OnuType EPON_ONU_TYPE_SFU MultiLlid 1 ProtectionType e_epon_onu_protection_none PonIfNum 1 SlotNum 0 Interface type EPON_ONU_INTER_TYPE_GE Number of port 1
BatteryBackup no
Multicast protocol igmpsnooping. FecMode disable. FecAbility support. Alarm disable. Port Isolation enable. Mac aging-time 300. IPV6 N/A. PowerControlSupply N/A. Service SLA 0. ExtOamVersion CTC21.
В ZTE на flash эта прошивка залита, как p1501c_ram_10.0.14a_1039.bin
В BDCOMe на flash она залита как p1501c.bin
